Judging from the pictures sent by LeTV's official microblog, the new LeTV Super TV retains the design of the new cloud base. The body is embellished with gold and bright, while other parameters are still a mystery.
As early as the beginning of 2015, there was news that LeTV was about to launch a new generation of super TV. The first size segment to be released would be a 55-inch super TV, with an all-metal frame, support for 4K, or the name X55 Air, and the price would be around 5,000 yuan. , and millet TV 2 55 inches (4999 yuan) quite.
It is reported that LeTV Super TV X55 Air will be improved in hardware configuration, operating system and functional applications, and will use the same manufacturing process as the X60S, but will use the full metal frame, cloud base and hardware configuration to adapt to more complex systems, And do a deep optimization of the UI. In addition, X55 Air will also support 4K, then in the 3D function, it will have what performance, continue to adhere to 3D features? In terms of functional requirements, this is even better than the Xiaomi TV 2 55.
In terms of price, the 55-inch X55 Air or around 5,000 yuan, between the price of 60-inch and 50-inch super TV, will still adopt the hardware price plus content service fee policy, which means that users will continue to pay for follow-up, if The promise of strengthening the content of Xiaomi TV's 55-inch TV is achieved, and the outlook for LeTV's 55-inch TV is very worrying.
Does LeTV be able to match the 55-inch Xiaomi TV? We will wait and see.
1.ANTENK Wire To Board Connectors are avialable in different terminations and sizes intended for use on a variety of applications. These connectors provide power and signal with different body styles, termination options, and centerlines. To find the wire to board set required, click on the appropriate sub section below.
2.Our products are widely used in electronic equipments,such as monitors ,electronic instruments,computer motherboards,program-controlled switchboards,LED,digital cameras,MP4 players,a variety of removable storage disks,cordless telephones,walkie-talkies,mobile phones,digital home appliances and electronic toys,high-speed train,aviation,communication station,Military and so on
Antenk Wire To Board Connectors Ranges:
Power Wire to Board
IDC Wire to Board
Locking Wire to Board
Latching Wire to Board
Fine Pitch Wire to Board
Wire to Board Connectors Information
Description
Wire-to-board connectors are used to interconnect printed circuit boards (PCBs) by using connectors attached to wires.
Specifications
Specifications for a wire to board connector include the following.
Wire-entry angle - There are three wire-entry angle styles: vertical, right-angle, and bottom-entry.
Wire size - Wire size is usually measured in American wire gauge (AWG), a standard for non-ferrous wire conductor sizes. The term "gauge" refers to the wire`s diameter. The higher the gauge number, the smaller the diameter and the thinner the wire.
Circuits or positions - With wire to board connectors, the number of circuits or positions may range from 1 to 120.
Pitch or center spacing - Pitch or center spacing is measured in millimeters (mm) or inches.
Lock to mating style - There are three basic lock-to-mating styles: positive, friction, and friction ramp.
Maximum current - The maximum current or current-carrying capacity is measured in amperes (A) and ranges from 1.0 A to 50. A.
Termination Methods
Crimp is the physical compression of a contact wire around a conductor to make an electrical and mechanical connection. Insulation displacement connectors (IDC) slice through the cable insulation to make a connection. Choices for termination method also include cage clamp, screw, tabs, and solder cups.
PCB Mounting Styles
With wire to board connectors, there are four choices for PCB mounting.
Through-hole technology (THT) mounts components on a PCB by inserting component leads through holes in the board and then soldering the leads in place on the opposite side of the board.
Surface mount technology (SMT) adds components to a PCB by soldering component leads or terminals to the top surface of the board. SMT components have a flat surface that is soldered to a flat pad on the face of the PCB. Typically, the PCB pad is coated with a paste-like formulation of solder and flux.
Press-fit and compression-style Board To Board Connectors are also commonly available.Wire to Board Connectors Information
Standards
Wire-to-board connectors carry approvals from various national and international organizations. In North America, they often bear marks from Underwriters Laboratories (UL) and/or the Canadian Standards Association (CSA).
A wire to board connector for the European marketplace should comply with the Restriction of Hazardous Substances (RoHS) and Waste Electrical and Electronic Equipment (WEEE) directives from the European Union (EU). Wire-to-board connectors that comply with other requirements are also available.
BS 9526 N0001 - Specification for multi-contact edge socket electrical connectors.
Wire To Board Connectors Series
Wire To Board Connectors,Wire Harness,Pcb Wire To Board Connector,Pin Wire To Board Connector,IDC Wire to Board,Locking Wire to Board,Latching Wire to Board,Fine Pitch Wire to Board
ShenZhen Antenk Electronics Co,Ltd , https://www.antenk.com